FMP Airsoft  

I was looking through Airsoft Atlanta for any deals, since I was buying a sniper and some parts, and I saw this beautiful bucking. Maple leaf has made and MR Hop for AEG's! I'll have to try it in my M14 since it needs a new bucking anyways!

FMP Airsoft  

Oops, forgot the link

https://www.airsoftatlanta.com/colle...up-bucking-aeg

Skara  

Yup, picked 2 up the other day, 50° hardness, along with 2 GBB/VSR ones and a bunch of Omega nubs and I-Keys

One is going into my E&L 74u (once I get the bloody outer barrel off) and the other will go into my ARP-9 :)

This evening/Tomorrow I'll test it on the ARP with weights up to 0.4 and see how it fares

__________________
Me bolty:
-Ares Amoeba Striker AS02 in FDE
-Ares steel cylinder with welded pins
-AirsoftPro piston and spring guide
-Guarder SP100
-Action Army hop wheel
-Stock hop chamber with a 3d printed arm
-Maple Leaf 50° MR-Hop + Omega nub
-Action Army 6.03x300mm steel barrel
-Samurai (@printedairsoft.co.uk) straight bolt pull handle and trigger
-FMA Spectre suppressor rethreaded for the barrel 23x1.5 thread
-cheap 4x32 scope

Me secondaries:
-Mk23 (ssx gen 1)
-Action Army AAP01

Masinmees  

I'm using 50 degree one with 410mm crazyjet GBB barrel in my P* M4 for few months now and it shoots like a dream. Probably the best combo I've used in my rifle.

FMP Airsoft  

Will the VSR one work with a Lambda barrel?

Skara  

if it's the VSR unbridged one, yes.
if it's the bridged VSR, no, you'll need to remove the bridge.
if it's the AEG barrel, no, you'll need the AEG rubber.

__________________
Me bolty:
-Ares Amoeba Striker AS02 in FDE
-Ares steel cylinder with welded pins
-AirsoftPro piston and spring guide
-Guarder SP100
-Action Army hop wheel
-Stock hop chamber with a 3d printed arm
-Maple Leaf 50° MR-Hop + Omega nub
-Action Army 6.03x300mm steel barrel
-Samurai (@printedairsoft.co.uk) straight bolt pull handle and trigger
-FMA Spectre suppressor rethreaded for the barrel 23x1.5 thread
-cheap 4x32 scope

Me secondaries:
-Mk23 (ssx gen 1)
-Action Army AAP01

Calebs0615  

Bought the 70° one for my l96 and they sent me the VSR one. I emailed them saturday and havent heard anything yet. 😒😒

Skara  

So, I put the AEG one in my ARP, it does lift 0.3s like nothing at 0.7J and sends them at at least 55 metres.
As soon as I replace the cylinder to fix the volume (really undervolumed atm) I'll test it again, but results seem promising so far!

Also haven't noticed any difference between the MR and the decepticon on my Striker so far, but again I fired 10 BBs.

More extensive test of the 2 rubbers will follow on Sunday (0.28/0.3/0.32/0.4g BBs)

__________________
Me bolty:
-Ares Amoeba Striker AS02 in FDE
-Ares steel cylinder with welded pins
-AirsoftPro piston and spring guide
-Guarder SP100
-Action Army hop wheel
-Stock hop chamber with a 3d printed arm
-Maple Leaf 50° MR-Hop + Omega nub
-Action Army 6.03x300mm steel barrel
-Samurai (@printedairsoft.co.uk) straight bolt pull handle and trigger
-FMA Spectre suppressor rethreaded for the barrel 23x1.5 thread
-cheap 4x32 scope

Me secondaries:
-Mk23 (ssx gen 1)
-Action Army AAP01

Skara  

Tested 0.28s today, haven't sorted the air seal yet.
Tiny bit of holdover got me 60 metres-ish. Very consistent too!

__________________
Me bolty:
-Ares Amoeba Striker AS02 in FDE
-Ares steel cylinder with welded pins
-AirsoftPro piston and spring guide
-Guarder SP100
-Action Army hop wheel
-Stock hop chamber with a 3d printed arm
-Maple Leaf 50° MR-Hop + Omega nub
-Action Army 6.03x300mm steel barrel
-Samurai (@printedairsoft.co.uk) straight bolt pull handle and trigger
-FMA Spectre suppressor rethreaded for the barrel 23x1.5 thread
-cheap 4x32 scope

Me secondaries:
-Mk23 (ssx gen 1)
-Action Army AAP01

FMP Airsoft  

With a ML nub or other?

Skara  

yes, the Omega nub, with a spacer between that and the arm because for some reason without it the unit doesn't apply enough hop.

__________________
Me bolty:
-Ares Amoeba Striker AS02 in FDE
-Ares steel cylinder with welded pins
-AirsoftPro piston and spring guide
-Guarder SP100
-Action Army hop wheel
-Stock hop chamber with a 3d printed arm
-Maple Leaf 50° MR-Hop + Omega nub
-Action Army 6.03x300mm steel barrel
-Samurai (@printedairsoft.co.uk) straight bolt pull handle and trigger
-FMA Spectre suppressor rethreaded for the barrel 23x1.5 thread
-cheap 4x32 scope

Me secondaries:
-Mk23 (ssx gen 1)
-Action Army AAP01

SiliconeSword  

Does anyone own a MAXX hop unit to test these in?
I'm really curious as I'm planning out my first DMR

__________________
We all know the guy that says he can split an atom, at 420 feet, with 1J, in the dark, and handcuffs, with a widebore, and a 25mm ER-hop……………

Where you can see my projects and other cool stuff
https://www.instagram.com/silicone_sword/
(\ __ /)
(= '.' =) This is a little rabbit.
(") _ (") Copy / paste it into your signature to help it dominate the world.

FMP Airsoft  

Unfortunately I do not. Version 7 gearbox M14 means a proprietary hopup unit..... Very sad indeed.

AsianGuy  

Are these MR hop supposed to be near as good as r-hop?
Sorry if it’s a silly question, I’m not too verse on the maple leaf bucking lines, and there are so many variant of them

FMP Airsoft  

Of the experience I have so far with the AEG one (macaron) they are certainly better than stock, but far from perfect. I know that a lot of people live the autobot, but I have not tested that. From what people say, it's like 95% of an RHop. But........ It takes considerably less time.