Pdi barrel problem with maple leaf autobot bu king. - Airsoft Sniper Forum
       

Go Back   Airsoft Sniper Forum > The Rifles > VSR Rifles
VSR Rifles TM VSR's

Reply
 
LinkBack Thread Tools Display Modes
Old 08-12-2019, 09:11 PM   #1
Jr. Sniper
 
plasticnoob's Avatar
 
Join Date: Nov 2017
Posts: 136
Pdi barrel problem with maple leaf autobot bu king.

I thought it would fit.... so the Pdi barrels dont work with maple leaf backings???
Attached Images
File Type: jpg 20190812_205902_1565658092485.jpg (91.4 KB, 20 views)
__________________
Check out my YouTube and Facebook channel of my Airsoft page @ Actual Airsoft Reviews or https://www.youtube.com/channel/UCDL...OtceZDNsCB_Xng and
https://www.facebook.com/ActualAirsoftReviews/
FPS 513 514 510 512 516
JG Bar 10 parts list build:
CJ 6.04x428mm
AA hop up
ML bucking 70 degrees
ML concave nub
AA zero trigger w/ 90 degree piston
AA m150 spring
AA spring guide
AA cylinder set
AA end cap (required for AA cylinder)
AA bolt handle
Skeee's TDC hop up
BSA Sweet .22
  Reply With Quote
Remove Ads
Old 08-12-2019, 09:33 PM   #2
Jr. Sniper
 
Blind Sniper's Avatar
 
Join Date: May 2018
Posts: 137
Maple Leaf buckings are for barrels withOUT a bridge. You can remove the bridge if you’re careful. Or get a nine ball, pdi w hold, or some other bucking if you keep the bridge. Many options.
  Reply With Quote
Old 08-12-2019, 10:31 PM   #3
Sodium   Sodium is offline
Jr. Sniper
 
Sodium's Avatar
 
Join Date: Nov 2017
Location: North Eastern U.S.
Posts: 137
I would cut the bridge off and then dremel/sand it down so there are no sharp edges.
  Reply With Quote
Sponsored Links
Advertisement
 
Old 08-12-2019, 10:58 PM   #4
Jr. Sniper
 
plasticnoob's Avatar
 
Join Date: Nov 2017
Posts: 136
Thank you guys! I will get my dremel out tomorrow and slowly work on it.
__________________
Check out my YouTube and Facebook channel of my Airsoft page @ Actual Airsoft Reviews or https://www.youtube.com/channel/UCDL...OtceZDNsCB_Xng and
https://www.facebook.com/ActualAirsoftReviews/
FPS 513 514 510 512 516
JG Bar 10 parts list build:
CJ 6.04x428mm
AA hop up
ML bucking 70 degrees
ML concave nub
AA zero trigger w/ 90 degree piston
AA m150 spring
AA spring guide
AA cylinder set
AA end cap (required for AA cylinder)
AA bolt handle
Skeee's TDC hop up
BSA Sweet .22
  Reply With Quote
Old 08-13-2019, 02:20 AM   #5
 
Plazmaburn's Avatar
 
Join Date: Feb 2013
Location: San Antonio, TX
Posts: 3,323
Send a message via Skype™ to Plazmaburn
I used a hand file to take mine off. Takes like 5 min. And you dont risk messing up your barrel with a dremel mishap.
__________________
Don't underestimate me. I know more than I say, think more than I speak, and notice more than you realize.
  Reply With Quote
Old 08-13-2019, 05:09 PM   #6
Sodium   Sodium is offline
Jr. Sniper
 
Sodium's Avatar
 
Join Date: Nov 2017
Location: North Eastern U.S.
Posts: 137
I agree with plasma. I'd highly reccomend using a file or sanding by hand, unless you are very good and careful with the dremel.
__________________
Some people are slinkies, not really good for much but bring a smile to your face when you push them down the stairs
  Reply With Quote
Old 08-13-2019, 07:27 PM   #7
Advanced Sniper
 
Join Date: Nov 2018
Posts: 645
Or, instead of marring the barrel by filing it - R-Hop it... A lot of work considering a ML bucking will give you similar results but then you could always repurpose it in a different rifle later that uses bridged barrels.
  Reply With Quote
Old 08-14-2019, 11:00 AM   #8
Jr. Sniper
 
ArcAngel's Avatar
 
Join Date: Jun 2014
Posts: 447
Both options are good. My recomendation if your going to cut the bridge, do a rough cut with the dremel and finish by hand if your good with dremel .

I cut all my pdi barrels, its easy, but in retrospect i wish i had kept one for an rhop setup to test with. But I have to say, im not at all unhappy with my 60 degree maple bucking. It shoots straight, what else could you really want?
  Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -5. The time now is 06:01 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
SEO by vBSEO ©2011, Crawlability, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.