AA Cylinder Head and AA Hop Up Unit

Duesrax · Jun 25, 2015

So I have both of the mentioned parts listed in the title but I cannot seem to get them to work together. I know that the head is a cloned laylax and the part in the chamber that won't let it work is a cloned PDI. Is there a way I can get them to work together though? My stock JG head doesn't have very respectable airseal while the action army one gives me perfect seal.

Sent from my XT1058 using Tapatalk

DillSS · Jun 25, 2015

What do you mean "work together"?

Plazmaburn · Jun 25, 2015

What is it doing?

Southclaw · Jun 25, 2015

I have seen this problem discussed before. It should be those spring tensioned black protruding knob things on the inside of the hop up. I believe 1tonne has a good bit of experience this bit.

Plazmaburn · Jun 25, 2015

Southclaw said:
I have seen this problem discussed before. It should be those spring tensioned black protruding knob things on the inside of the hop up. I believe 1tonne has a good bit of experience this bit.

Oh yeah! I forgot about those. I had mine really loose (I think) and it worked just fine for me.

Duesrax · Jun 25, 2015

After I loosened the black screws, it works sometimes but will chop bbs like 1/5 of the time.

Sent from my XT1058 using Tapatalk

Duesrax · Jun 25, 2015

DillSS said:
What do you mean "work together"?

Be compatable

Sent from my XT1058 using Tapatalk

Southclaw · Jun 25, 2015

I belive you may have to cut the spring, somewhere I saw mention of using a bit of tee shirt material for something. Can't quite remember what for though. Go check out the AA hop up thread that was started a while ago, several people solved this problem in various ways on that thread.

1tonne · Jun 25, 2015

Before cutting the spring for the Black guides try stretching the Mag spring. This will push the bb against those black round guides and push them up further and so the bb's will not get cut in half.
I have the AA cylinder head and AA Chamber and they work fine. I did not have to cut the springs. I only had to make sure the mags were strong enough to push the black guides up far enough.

Duesrax · Jun 25, 2015

1tonne said:
Before cutting the spring for the Black guides try stretching the Mag spring. This will push the bb against those black round guides and push them up further and so the bb's will not get cut in half.
I have the AA cylinder head and AA Chamber and they work fine. I did not have to cut the springs. I only had to make sure the mags were strong enough to push the black guides up far enough.

I can't seem to get the spring back in the mag.. How did you do it?

Sent from my XT1058 using Tapatalk

1tonne · Jun 25, 2015

It can be a big mission but I have made my own way.
The stick shaped part that the spring fits onto, glue that onto one side of the mag (super glue). Then once it is dry put the spring and push it all the way on. Make sure the bb guide (the black bit that pushes the bb's) is on it. I then got a 5mm rubber tube and fed it through where the bb's exit the mag (so the square shaped part that stops the bb's spraying everywhere). The lie the rubber tube down in the track that the bb's would be pushed along and this pushes up against the spring holding it on the stick piece. Carefully put the top side of the mag on and screw it in place. Pull the tube out from the mag and the mag should be ready to go.
So the tube is only used to hold the spring onto the stick and the tube fits down where the bb's track along. Then the tube it removed once the mag is together.
(Maybe I should do a tutorial some day with pictures)

I have done it without the tube but it takes a lot of frustrating time.

Duesrax · Jun 25, 2015

The problem is fixed! I have near 100% airseal throughout the whole gun.

Sent from my XT1058 using Tapatalk

1tonne · Jun 25, 2015

Was it the Mag spring?

Duesrax · Jun 25, 2015

I believe so

Sent from my XT1058 using Tapatalk

AA Cylinder Head and AA Hop Up Unit

Duesrax

DillSS

Plazmaburn

Southclaw

Plazmaburn

Duesrax

Duesrax

Southclaw

1tonne

Duesrax

1tonne

Duesrax

1tonne

Duesrax

Top Contributors this Month

Recommended Communities