Airsoft Sniper Forum - Search Results
       

Go Back   Airsoft Sniper Forum > Search Forums
Showing results 1 to 25 of 70
Search took 0.01 seconds.
Search: Posts Made By: Vsr10
Forum: VSR Rifles 04-29-2020, 06:37 AM
Replies: 8
Views: 238
Posted By Vsr10
whats wrong with decepticon , i found them very...

whats wrong with decepticon , i found them very accurate up to 60 m i dont have experience with longer shot as 1 j limit[/QUOTE]
Stock bucking can be accurate dead on up to 60-70m with little arm...
Forum: VSR Rifles 04-27-2020, 11:24 PM
Replies: 8
Views: 238
Posted By Vsr10
I don't have nub, just stock arm that i modified,...

I don't have nub, just stock arm that i modified, i think this may be problem

Arm is to much the right, i sand and shimmed the arm, just wait opportunity to test, arm that i modified is basically...
Forum: VSR Rifles 04-25-2020, 09:45 AM
Replies: 8
Views: 238
Posted By Vsr10
No matter what bucking, i still can't solve...

No matter what bucking, i still can't solve stupid curving to the right after 70+m
First i use stock bucking, shim the arm and sand it a little in this shape on picture, and i got 65-70+m dead...
Forum: VSR Rifles 04-22-2020, 12:24 PM
Replies: 8
Views: 228
Posted By Vsr10
they have them in https://www.bulltrigg.com/shop/...

they have them in https://www.bulltrigg.com/shop/ for 2.99 eur dont know how much for postage[/QUOTE]
Probably a lot, i will find something that will fit
Forum: VSR Rifles 04-22-2020, 12:22 PM
Replies: 1
Views: 99
Posted By Vsr10
Buy ML head or something that will fit, i doubt...

Buy ML head or something that will fit, i doubt it that you can new thread on pps head, probably not enough material
Forum: VSR Rifles 04-20-2020, 02:52 PM
Replies: 8
Views: 228
Posted By Vsr10
i will go same as you but this big shim i think...

i will go same as you but this big shim i think is there to cover actual whole in sear cheaper to replace if something wear off[/QUOTE]
I will make it soon, just spring may be a problem to find
Forum: VSR Rifles 04-20-2020, 07:18 AM
Replies: 8
Views: 228
Posted By Vsr10
I thinking the same thing, but to make that oval...

I thinking the same thing, but to make that oval hole to the sides of trriger not to sear
Forum: VSR Rifles 04-19-2020, 03:27 PM
Replies: 8
Views: 228
Posted By Vsr10
I have this pic, but don't understand how is the...

I have this pic, but don't understand how is the sear that close to the spring guide stoper, and it works, only obvious choice is to sear slide up and down when piston slides above the sear, i make...
Forum: VSR Rifles 04-19-2020, 06:18 AM
Replies: 8
Views: 228
Posted By Vsr10
Bull trigger

Does anyone have picture of disassembled bull trigger, need some info for my diy 90 trigger
https://youtu.be/hrpZgvNDcjg
Forum: VSR Rifles 04-19-2020, 06:15 AM
Replies: 4
Views: 158
Posted By Vsr10
Owner said it does, he uses bigger airbrake also...

Owner said it does, he uses bigger airbrake also for this head
Forum: VSR Rifles 04-18-2020, 07:47 AM
Replies: 10
Views: 335
Posted By Vsr10
Yes it is, i make my own 90 trigger First...

Yes it is, i make my own 90 trigger
First prototype is almost done
https://youtu.be/hrpZgvNDcjg
Soon al be making a better one with higher fps boost
Forum: VSR Rifles 04-12-2020, 10:19 AM
Replies: 4
Views: 158
Posted By Vsr10
Cylinder head

Does anyone have cylinder head like this? 6.9mm inner diameter almost all the way to the end, 12mm deep, one buddy told me that is the stock head for mlc 338,
Is this good for more fps? Stock head...
Forum: VSR Rifles 04-09-2020, 05:10 AM
Replies: 30
Views: 600
Posted By Vsr10
I have 430 mm barrel already, 6.03mm So that...

I have 430 mm barrel already, 6.03mm
So that part is ok
Forum: VSR Rifles 04-09-2020, 03:31 AM
Replies: 30
Views: 600
Posted By Vsr10
Whats is the correct lenght for 0.43? I mesure...

Whats is the correct lenght for 0.43?
I mesure my pps cylinder, it's have about 90mm x 22mm (o ring isn't visible when bolts is pulled)

90x23mm is the stock cylinder (o ring is visible when bolt...
Forum: VSR Rifles 04-07-2020, 01:49 AM
Replies: 30
Views: 600
Posted By Vsr10
I will using 0.43,or maybe 0.45 for now.. Just...

I will using 0.43,or maybe 0.45 for now..
Just need good spring to get 3.5j or 4j,rapax 3+ lost about 20% strength, need to find strong spring but it's must be shorter than rapax to not lose to...
Forum: VSR Rifles 04-06-2020, 05:42 AM
Replies: 30
Views: 600
Posted By Vsr10
One off topic question, is the stock vsr buckings...

One off topic question, is the stock vsr buckings same for bridged and unbridged barrel? I want to open bridge on my steel barrel so i can use ML buckings, hope that will not make problem if i want...
Forum: VSR Rifles 04-05-2020, 04:46 PM
Replies: 30
Views: 600
Posted By Vsr10
Am using 0.43,and have 430mm inner barrel

Am using 0.43,and have 430mm inner barrel
Forum: VSR Rifles 04-05-2020, 04:43 PM
Replies: 30
Views: 600
Posted By Vsr10
I will investigate why isn't catching tomorrow

I will investigate why isn't catching tomorrow
Forum: VSR Rifles 04-05-2020, 02:22 PM
Replies: 30
Views: 600
Posted By Vsr10
First i try to make piston shorter, then we will...

First i try to make piston shorter, then we will see what next to do,only i don't understand how yours short piston works but mine short plastic piston won't catch sear with pps cylinder
Forum: VSR Rifles 04-05-2020, 01:16 PM
Replies: 30
Views: 600
Posted By Vsr10
I rather be making a longer groove than add sorbo...

I rather be making a longer groove than add sorbo to the piston and lose cylinder volume where is most important, but if yours piston is already shorter and works great , groove must be already long...
Forum: VSR Rifles 04-05-2020, 05:14 AM
Replies: 30
Views: 600
Posted By Vsr10
That is the case with stock cylinder,i want to...

That is the case with stock cylinder,i want to make same principle on pps, since O ring isnt visible when the bolt is pulled back, there's another question, pps groove is a bit shorther than a pps,...
Forum: VSR Rifles 04-05-2020, 04:28 AM
Replies: 30
Views: 600
Posted By Vsr10
You can make mark through the groove on piston...

You can make mark through the groove on piston and cylinder when bolt is pulled back, when stock is removed , and later when you do a cleaning, you can put piston in cylinder without spring, align it...
Forum: VSR Rifles 04-05-2020, 01:27 AM
Replies: 30
Views: 600
Posted By Vsr10
Nice diference, is the piston head of shorted...

Nice diference, is the piston head of shorted piston visible in the groove when is bolt pulled back? Like the O ring of my stock piston?
Forum: VSR Rifles 04-04-2020, 05:51 PM
Replies: 30
Views: 600
Posted By Vsr10
I making my own 90 trigger because price is...

I making my own 90 trigger because price is ridiculous for that part,
I want to shorten the pps piston because with rapax 3+ i only getting 500fps, stock plastic one gets me about 510 fps, but...
Forum: VSR Rifles 04-04-2020, 05:46 PM
Replies: 30
Views: 600
Posted By Vsr10
Woow, almost 100fps diference Do you maybe...

Woow, almost 100fps diference
Do you maybe have face to face picture of shorten and longer piston?
I can shorten it, my frend will make me shorter piston end, just only concern is that O ring will...
Showing results 1 to 25 of 70

 
Forum Jump


All times are GMT -5. The time now is 09:45 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
SEO by vBSEO ©2011, Crawlability, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.