Airsoft Sniper Forum banner

cylinder

  1. Rifles & Parts Reviews
    Has anyone tried this cylinder set?, or the cylinder alone?, looks well done and it's very cheap PPS Cylinder Upgrade Kit Stainless Steel CNC Machined for VSR10
  2. VSR Rifles
    Hi Everyone! This is my first post here as I am a new member here and I'm hoping someone here can answer a question for me that I can't seem to find the answer to myself. I built a JG BAR-10 a few years back when I was younger (AKA my brother told me what to buy and did it for me) and the...
  3. VSR Rifles
    Hello, i am running a PDI BoreUp Cylinder with a PDI Hop Up Chamber, but i am unsure which barrel would be the best for this setup. I´ve read that, because of the cylinder volume of the bore up, i should use a inner barrel above 500mm - so i found a PDI 6.08 500mm inner barrel , would that...
  4. Others
    Hi folks! Any one knows the dimentions (lenght and diameter) of this kind of cylinder/ piston? APS2 / Type96 / APS SR2 (MB06) / M99 SW / M24 SW / M24 CA???? This is the link of the product Kit Dark APS2 / Type96 / APS SR2 (MB06) / M99 SW / M24 SW / M24 CA
  5. General Sniper Talk
    Has anyone ever done this, and more importantly, succeeded? It is this PDI end cap: PDI VSR-10 End Cap I know that you can just buy the AA end cap to go with the AA cylinder, which is what I already have. I am just curious as to whether anyone has successfully put the PDI end cap on the AA...
  6. General Sniper Talk
    First of all, it's "source", not "cylinder"- some of us are HPAholes :yup: Primary Intrigue: Is there convincing evidence that the "ideal" (creates the most muzzle energy- adjusting barrel length causes reduction) source/barrel volume ratio also creates the most accurate/precise trajectory...
  7. Type96
    Hello, I recently upgraded my mb06 with the pps upgrade set (aluminium springguide, piston and new spring). I kept my old spring in because my field limit is 500fps and I didn't want to damage my trigger. But now when I cock the bolt, there are scraping marks on my cylinder where it passes...
  8. Rifles & Parts Reviews
    Well guys, i have the m28 with the stock cylinder for 3 years and i look the cylinder and this was happen: the edge is curving!, for now it has not given me problems, but I am afraid that soon I will have problems. Has this happened to someone?
  9. Rifles & Parts Reviews
    Hi guys, im in the proyect to make a steel cylinder for my e1m28 since there's no steel cylinder out there!, but the steel tube has a seam inside. Do you think that seam will be a problem to the piston seal?
  10. VSR Rifles
    Is it apsolutely necessary for me to upgrade my cylinder on my bar 10 as they are quite pricey. Is it ok to leave it stock or do i have to upgrade the cylinder head or the whole cylinder and head? I'm currently shooting at 490 fps. If it is mandatory, please say a good, but budget friendly...
  11. General Sniper Talk
    Please advise, I have an EdGi cylinder and cylinder head in my VSR, along with his 45/55° piston .. and I want to eventually change it to a 90° setup. My question is: is it possible to put a different piston from another manufacturer (e.g. AA) into this cylinder? ..and if yes, what are the...
  12. VSR Rifles
    So im going to try to explain this the best i can... basically i have a action army cylinder and an orange action army piston. however, the air seal is really poor which I belive is really effecting my consistancy. (from holding my thumb over the cylinder head and shooting). Im 99% sure its to...
  13. VSR Rifles
    I could not find a link in any other threads, however can someone give me a link for a steel cylinder (PPS makes one) for a well mb02/mb03? Everything I have seen is out of stock or cannot ship to the United States. The stock handle separated from the cylinder shaft where it was crimped together...
  14. VSR Rifles
    I'm guessing this is the closest thread to post in because the Echo 1 M28 is so similiar to the VSR. Here's the issue. I have an Echo 1 M28, upgraded with a ranger piston & custom sear set. My bolt just snapped, at least the little tab to supposed to keep it in place. That need to be...
  15. General Sniper Talk
    Looking for advice, guide or mod how to make smooth pull. I am using snow wolf M24 with Airsoftpro parts. Sorry for my bad english.
  16. VSR Rifles
    Hi everyone I've just decided to mod my VSR and after reading a lot of posts here I have found the Cylinder Barrel Ratio one. My country limit is 330 Fps (1J here in Italy), I feel like I can use BBs as light as 0.32g to 0.43g BBs for my rifle in order for me to stay under the limit and not to...
  17. VSR Rifles
    Hi all, I got an Action Army hop up chamber and new barrel (Laylax 6.03 550mm) for my VSR-10 a little while ago. (I believe the gun to be shooting in the 420-450 range.) I got everything set up right with the hop up and barrel and it was shooting amazingly well, but am struggling with another...
  18. VSR Rifles
    Hello everyone, so about a year ago, I've decided to build my VSR-10. So, I went for the JG BAR-10, because it's cheaper and I wanted to change all the internals anyway. Internals: 433mm 6,03 Prometheus barrel, PSS-10 hop up chamber (AirsoftPro red hop lever + PSS-10 bucking), AirsoftPro...
  19. Type96
    Hey guys,does anyone know where i can buy a cylinder (even a stock one) in europe or somewhere that i don't need to pay a lot for shipping? Thanks for your help in advance.
  20. L96 Rifles
    Hi everyone, first time here so please bear with me. I've decided to upgrade my ASG AW .308 rifle. And I'm trying to change the cylinder, however I can not remove the bolt handle at all. I've removed the grub screw located underneath the block but the screw (I'm guessing is a screw) just will...
Top