Airsoft Sniper Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 28 Results
  1. VSR Rifles
    So I currently have an airleak going on on my AA chamber and i need a bit of assistance on fixing it. I am pretty sure the air is leaking from my hop up rubber and nozzle connection point. It isn't a huge issue because I could just cover this hole with strong tape and it was shooting fine...
  2. Type96
    Note: This issue has been solved, look further below for the TL;DR/Explanation. Hello So, my platform is the Well MB08, which came with Well's full metal trigger box and cylinder internals. I've just bought the airsoftpro type96 trigger box, the action army teflon cylinder, and the guarder...
  3. General Sniper Talk
    When i pull back the piston to cock the gun, it cocks normally, but when i try to push the piston forward to it's original position, the gun fires automatically. The Rifle is old, which has me thinking it's probably a used up part that needs to be replaced. But i don't know which part. Thank you...
  4. Novritsch Platforms
    Hello. I have had problems with left-curving bbs. I have dissasembled and assembled the cylinder and those components, along with the hop up unit mulitple times but I cannot find the problem. I took pictures of the different components and uploaded them to imgur and was wondering if anyone could...
  5. Novritsch Platforms
    Hello. I have been having problems with left curving shots. Things I have done/checked: Removed and put on the scope, scope rings and adjusted the scope to be as aligned as possible. Dissasembled the rifle to check the hop up chamber, all parts look good from what I could see, some dirt on the...
  6. Novritsch Platforms
    Hello. I have had problems with my SSG10 ever since I dissasembled the stock and cylinder to clean and relube the components around the cylinder. (NOTE: I didn't touch the hop up chamber, nor the trigger box). The problem is when I have pulled the bolt back and then return it down to the firing...
  7. VSR Rifles
    lately I've got lots of problems with my vsr the consistency is everywhere and I have the issue where the bb curves after about 150-200ft. I think it is the barrel or myb the bucking but i hear the hop up chamber can be the problem also. Soon i will make an order for the new 6.01 barrel and a...
  8. Novritsch Platforms
    Hello, I have just brought an ssg24 with a m140 spring installed. I used it at the weekend with 0.40g bbs but the hop-unit was going from dropping on one click and flying up on the next click. Do you think that I need to get heavier bbs? As when it was chronoed it was shooting around 500fps...
  9. VSR Rifles
    I'm new to airsoft sniping upgrades and i've come to a very wierd issue with my hopup, I bought a Maple leaf 70 degree Super bucking and i've also tried multiple of other bucking but all of them have the same problem, When i apply hopup with any of the upgraded hopup buckings the bb's just drop...
  10. Sidearms, Optics, Gear, and Accessories
    I need some good advice, I have this gun about 5 months ago almost every day I use it for target shooting, like about 200-300 shots X day, and a few days ago I started shooting in full auto and besides spitting gas everywhere . I did a clean maintenance and continues with the same issue...
  11. VSR Rifles
    Recently i've finished building my rifle. Buying parts and was really long and hard proces as almost everythin i bought was broken in some way... So i decided to go with EdGi parts to eliminate the factory overlook. That's the list of my parts: - EdGi 6.00 435mm bull barrel - EdGi Cylinder and...
  12. VSR Rifles
    Hi Guys, I've just got my ASPro 90 trigger v3, built it into my VSR and realized, its hard to pull. M150 spring the spring guide and cylinder came with the trigger. Any idea?
  13. VSR Rifles
    Hey everyone, I'm brand new to this page and my name is Mike! I recently just got back into airsoft through a few friends and am loving it. I just bought a JG Bar 10 G-Spec a couple weeks ago and have done the following mods: 6.03 inner barrel Angel Customs Piston Action army M170 spring Angel...
  14. VSR Rifles
    Hey guys can you give me a hand, my vsr is acting up a little bit. Basically I had to take the receiver out of the stock because the spring guide stopper came loose and so I put it back in and secured it with electrical tape, after that i decided to mess a tiny bit with the trigger pull and...
  15. General Sniper Talk
    Hello Guys, This is my first post, unfortunately about a new barrel with problems. I bought an EdGI kit for my M40a5 ares, after installing (don't worry about it I'm the first oficial gunsmith of ares in Brazil) and shooting I noticed something was wrong. I know that the barrel is conical, my...
  16. VSR Rifles
    Dear ASF Friends, I have just done my first build over the past 3 weeks and have now assembled everything, all the parts are PDI, the cylinder set the receiver, the inner barrel the hop up and the trigger set. I use a Boreup cylinder set and trigger (and of cause receiver) Yes i know Boreup is...
  17. VSR Rifles
    Hey there, Bought some spare magazines of TM to my BAR10 and they aren't feeding well, only the first bb shot's.... Aprecciate any help :tup::tup: Cheers JauTz
  18. VSR Rifles
    Hello, I have Echo1 M28 spring rifle and it just started to mis-feed. After replacing stock cylinder with Angel Customs cylinder and cylinder head (got on evike.com) it started feeding whole magazine into cylinder chamber. I've googled for the problem and majority of forum posts were indicating...
  19. Longrange AEGs
    Ok so my DMR recently started having issues, my bbs are curving to the right after about 100ft. I am using .25s but I am changing to .3s, my gun is shooting a solid 400fps and I have a Madbull Black Python 6.03 509mm tightbore installed. Any ideas? Also I'm looking to flat hop my gun and am...
1-19 of 28 Results
Top