Airsoft Sniper Forum banner
range
1-15 of 17 Results
  1. General Sniper Talk
    What are the differences between the degrees in the hop up (50° 60° 70° ecc) in termes of: bb weight? range? Power in Joule lost when hop up is activated? I don't know if this question was already done but I've not found anything regarding this so I asked, hope that is the right section.
  2. VSR Rifles
    Hi, i have a Gspec and have upgraded with a "action army vsr 10 90 degree s trigger set" and also a M150 spring. I want more range on my sniper as i still can only use .25 with my sniper as i dont get enough lift or range with the heavier bbs. i want to use .3 - .35 and ive been told the only...
  3. VSR Rifles
    I had the opportunity to test out the barrel/cylinder ratio and it did not end as expected. First i tested the 430mm 6,01mm barrel and the results were awesome. Longer range with heavier bbs and accuracy was also on point. I cut it down on the milling machine and carved the end so there was no...
  4. VSR Rifles
    Recently I have been thinking i have 0,42 grams and 0,50 grams but i want to try 0,6 grams and i do not know what is the advantage between 0,5 and 0,6. I didn't even use 0,42 grams a lot myb a few mags for testing but now i will try and test them against 0,5 (0,5 are gray and hard to see thats...
  5. General Sniper Talk
    Hi, Hopefully the combined expertise on this forum can assist. I have to design a ww2 shooting range at a museum next year (in the UK). In previous years we have run muskets, crossbows and longbows. What I am looking for is advice on the best rifle setup that satisfies the following. fast...
  6. General Sniper Talk
    I got my JgBar10 resealed by a gunsmith last week, and he found out after resealing my cylinder that the airleak was coming from the hop, so what he did was he replace my old hop with a new one (non branded) and he said to me that the hop bucking? (the metal sealer for hop) would not fit the hop...
  7. Sidearms, Optics, Gear, and Accessories
    I'm looking for either actual recommendations, or input on what makes a LRF good for airsoft. So far: - Waterproof - Low minimum range - Low error - Gyroscope (for angle) - Anti-fog/glare Right now I'm looking at the Sig Sauer KILO line. Thanks in advance. I'll try to update the thread if I...
  8. Longrange AEGs
    Hi guys, I would like to ask your help to find the problem in my G&G GR25 that does not have enough range. The stock barrel had a hard scratch so had to be replaced. In the meantime also wanted to tune up to our field limits: 500FPS (0.2g) So changed the spring and the barrel only: Had a...
  9. General Sniper Talk
    Hi everyone, my name is Simone, I'm from Italy. I've always been in love with airsoft sniping, but where I live, the legal limit of any airsoft gun is set to 328fps @0.20g BBs. I actually can buy an SSG24, it comes with an M90 Spring and shoots at 300fps @0.20. After many researches, I...
  10. General Sniper Talk
    Hello, this is something I started noticing with my rifle as I used it more and more. When I slide my hop up arm back to place more back spin on the bb I get less range! Any ideas what may be causing this? I use .36 g bio bbs Rifle is a UTG M324 that I modded to accept VSR 10 barrels and...
  11. General Sniper Talk
    First off, I want to ask you guys something. I have a jg bar-10, 520 fps perfect compression (i can put my finger at the end of the barrel and maintain for quite a while and no air escapes). I shoot madbull .36g bbs, washed and I use them with my type 96 and I have no problems. I have an action...
  12. VSR Rifles
    I have co2 sar 10 (600fps): -inner barrel 540mm 6.01 VSR A2A -A+ VSR hop bucking How I can increase accuracy and range?
  13. General Sniper Talk
    Ive had an E1 m28 for about 1 and a half years and I love the gun, but I've so many people say they've hit targets at 150-200 feet. Now i don't know if its an exaggeration or if its the gun but for me 150' is about the max. My main concern is range as accuracy is a different subject. I have both...
  14. Rifles & Parts Reviews
    Hey everyone, I am currently trying to stabilize my project rifles long range grouping as much as possible. I use an Ares CNC AW338, its been HPA converted and equipped with a real steel stock. I can send rounds with a flat trajectory to the 300ft mark but my grouping could be better. I have all...
  15. General Sniper Talk
    So I drilled four holes near the end of my barrel and put screws in to adjust the bend of the inner barrel.(cheese man's idea). I would adjust the barrel down and it would make it shoot down, I would adjust the barrel to bend up and it the bb would go up at about 175-200 feet and then back down...
1-15 of 17 Results
Top