Hello I just got this gun as a gift:
So I’m not in on this with any money so far, but I was wondering what parts does this thing even take? I’ve seen some people say that it’s a Marui clone so it can take those bits, and I’ve seen others say that it’s a...
Hello, I wanted some advice with the AST-01. I have heard mostly negative things about the AS-01, though have decided to get an AST because I want to snipe to have fun, and don't really care if it isn't the best performing rifle on the field. (Though I do want it to be good.) I am aiming for...
i have the tm vsr 10 and so far and im looking to upgrade a few parts. i have found the ACTION ARMY D01-024 VSR-10 6.01 Precision Inner Barrel 430mm, Action Army Hop Unit VSR-10 and the Maple Leaf MR Hop Up Bucking 70°, will these all fit together? I already have the action army trigger set and...
I am planning to upgrade my cyma 701b with the following upgrades:
Action Army VSR 10 specialised trigger
Action Army VSR 10 Teflon coated masamune cylinder
Maple leaf 70 degree hop rubber
Maple leaf 428mm 6.02mm inner barrel
Action Army VSR 10 hop up chamber
Action Army spring guide...
So I just recently bought a WELL VSR-10 Based Sniper and I'm looking to upgrade the entire sniper.
The parts I'll upgrade are
1- Springer Custom Works v9.2 Trigger
2- Action Army 90 degrees Piston
3- LayLax 190SP spring
4- Maple Leaf Deception 70 degree hop up
5- Action Army Hop Up Chamber
My goal is to have more consistent shoots on 70-80 m
currently i am reaching them no problem and with little wind i can shoot down a can of beer on 73 m with 3-4 shoots.
also im having trouble zeroing it in sometimes (i think its the scope tho).
on a non-little wind situation my shoots are...
Id like to upgrade my stock Well Mb05 to around 500fps shooting .36 or .4 bbs
This is my first sniper upgrade and im unsure where to start and id like to know what youve all done previously.
What i think ill need is :
A New Barrel (500mm long x 6mm - 6.03mm from what ive heard)
Hi folks! Any one knows the dimentions (lenght and diameter) of this kind of cylinder/ piston? APS2 / Type96 / APS SR2 (MB06) / M99 SW / M24 SW / M24 CA???? This is the link of the product
Kit Dark APS2 / Type96 / APS SR2 (MB06) / M99 SW / M24 SW / M24 CA
I'm new here so take it easy on me :)
I recently bought a new stronger spring for my sniper. Obviously the bolt pull is going to be tougher. But what I wasn't expecting was the push to change. It's not difficult to push in, but it is noticeably more resistant. The spring I put in was about a...
Alrighty then, So i'm completely new to this forum and relatively new to airsoft sniping and airsoft in general. I usually play a lot of CQB running my 1911 but recently started playing a lot more outdoors and after renting a Well L96 i had to get myself one and thus had my new Cyma 703 thrust...
Hi everyone, im planning to get a jg gspec since i've seen a good offer on a site. I'm planning to replace the cylinder, hop up chamber, piston, trigger etc... but i want to know if is it possible to use a 430mm inner barrel, since I already have a mapleleaf crazy jet, and i dont want to get a...
Hi!, i wanna know which blowback housing is more durable for my glock 17, mine glock has the zero hammer design and i really don't know if that design can wear or damage the bbu in the rear part, (that gap where the hammer rest) i search for some BBU upgrades and i found this brands: guarder...
I'm in the doubt of which O.B. is better for a metal (pot or aluminum slide), I do not remember if I read it or if I saw it in a video where it mentions that the O.B. made of steel can damage or "eat" the slide being softer metal, then should I buy an O.B. made of aluminum? Here I have some...
i am looking for a few upgrades on my A&K SVD AEG, can someone please provide a list of stock internal parts as mine did not come with a user manual, and a list of compatible parts for upgrading. Thanks in advance for any and all info provided.
Hi, so I'm new to the sniper sneaky stuff. I decided to change from aeg (ASR 115) after it died and got feed up with all its problems. Maybe a project Lazarus for that m4 as a DMR. Anyway now I want to go for a vsr build. I plan to take a bar 10 because there is no point in taking TM VSR 10...
Hi guys, im in the proyect to make a steel cylinder for my e1m28 since there's no steel cylinder out there!, but the steel tube has a seam inside. Do you think that seam will be a problem to the piston seal?
Is it apsolutely necessary for me to upgrade my cylinder on my bar 10 as they are quite pricey. Is it ok to leave it stock or do i have to upgrade the cylinder head or the whole cylinder and head? I'm currently shooting at 490 fps. If it is mandatory, please say a good, but budget friendly...
So this is the setup I'm running at the moment, please comment on any improvements that I could make or anything wrong. Cheers.
Crazy Jet 6.04 or Action Army 6.03 inner barrel (advice on which one please)
Maple leaf 60* autobot bucking
Maple leaf omega nub