So I want to know anyone experience on this gun. So here are my basic question.
Out of the box can it outrange a clone gun. (Hopefully)
Is it somewhat cheap to upgrade?
Yes I have read the old svd post. I have google skills and have scour alot of forums.
Can it reach 300 feet.
Should I get this as a budget sniper over the extensive G&P m16 project that will like cost me 500+dollars.
Are these good for the SVD
All airsoft pro parts 100 dollars. (Hop up, Piston, Piston catch)
Guarder Black bucking
Matrix m150 spring that somehow shoots 550-600 fps.
Prommy 650 barrel. Or maybe Edgi 6.05 with porting if I get enough money.
Scope of course.
.4 or .36 bbs.
To upload FPS want PSG1 spring or screw spring piece in some other spring by AEG.
Would make testing, depending on which is placed the extra spring, and will be changing the fps, you try and how many coils you need.
I have it in ATOZ close behind with about 5 coils of spring 130, 150 and wearing entire.
That is a 150 and 5 coils of 130. To have a few fps less than 550 (546fps)
Personally if you find ATOZ get this better and not the A & K
(I am afraid that this time I execution the grammar :-[)
300ft is do-able (according to the kids on Google).
I'm running a Systema 300% PSG1 spring, Madbull 6.03 and various AirsoftPro internals (not the new hop unit).
I think I'm using .30 BBs, but it's been so long since I used the SVD, I'm not sure... Maybe .36s.
With a Prommy hard bucking and a few double feeds now and then, I'm reaching 70-80 yards (torso sized grouping).
If I had a 400% spring it would give the extra "oomph" to hit the magic 300ft.
Do you mean it's hard to cock the bolt and the trigger pull is too heavy?
I did notice my trigger pull is quite a bit heavier with the new sear fitted.
Sure you can shoot it out to 300 feet with ease..... just figure out how high of an angle you need to hold the gun and shoot for the moon
Sorry couldn't resist
I would start with trying to get as much accuracy out of the rifle as you can. Then go from there. Just make sure that you are able to hit what you are aiming at before you try to get it there at a zillion fps.
I mean it is difficult to pull someone back when the bolt of the gun it's a lot of FPS, and even more difficult if you have to throw a lot of shots in no time.
It is completely different than a VSR or a L-96 bolt
Is very little surface pressure on the finger and without a glove is tough.
So I give you 500 dollars. You can pick either one of these guns to upgrade pick which one and what upgrades you would do.
UTG L96 (well l96)
Echo 1 M28
G&P M16vn (AEG)
A&K SVD
JG Bar 10
Well G96( Looks really pretty and I heard easy to get to 300 feet. I like it looks smexy.May not be hpa rigged because with some mods supposedly very accurate. And the fact I have no hpa rigging skills.)
Walmart pistol.
Walmart clear m4 with Polarstar internals =)
L96. I can get those up to about 530-550 fps with only teflon tape and a new oring. Then, for ~130 bucks, I buy the PDI hop chamber and a prommy 6.03 barrel. Then, for about 5 bucks, I buy a Guarder clear bucking, or many people like the w-hold bucking too. I then use the rest on foam (cushion stock, wrap barrel, etc.), scope, and a bipod.
I would buy this list. Yours is fine, just not what I would pick.
Polar Star piston
And a new spring guide/spring of your choice.
Laylax zero Trigger
PDI hopup chamber
Prommy 6.03 Steel barrel (500 mm)
Hop rubber of your choice, guarder clear or PDI w-hold bucking.
That's it! Then, just tape it up, floss, etc. However, for cheapness, just buy the piston, the hop chamber and barrel, then the z-trig, then the guide and spring.
Wow sniping is expensive it is killing my piggy bank. Maybe I should just go with the G&P m16.
Hey Cheese what do you think about this
G&P m16vn
Shs high torque gears
JG red motor
Guarder black or pdi bucking
m150 spring
"special" silly putty (Really JB weld)
Use of Dmr guide.
New Cylinder set with head and everything.
I knew it. You always seem to hang out in the bolt actions threads. By the way what guns do you run. Again should I get a Dmr or a sniper. I know this is one of them stupid questions.
It is probably the most expensive and time consuming role. That is for sure. Guys throw down hundreds of dollars for rifles, and thousand or so for parts. Not to mention the hours of work one them with many sleepless night.
Just be sure you don't use all your money for airsoft, because soon you will realize they just shut your water off.
I have run a Tanaka M700 AICS, 2 UTG type 96s, a VSR-10, a Kokusai Crimebuster M16A1, and a Kokusai Crimebuster SR-15. I have also used an A&K SR-25, but I only did routine maintenance for it, no parts selection, I just installed them, shimmed, and corrected the AoE.
I know what you mean about sleepless night. I when I built my jg G36 dmr. I want insane over the entire night. Thanks goodness I had mega tea I wasn`t tired.Went to school and still felt normal. My goodness mega tea has soo much power.
Thanks Bob good link. Oh yippee less karma every single day. I learned a new mod and his name is bob yay. Because the piston is 90 degree does that mean I might be able to use l96 pistons in there or do I have to get the Airsoft pro one. Ok now I just said screw you l96. I want either the A&K again or the G&P m16vn. Both are vietnam guns. Just which one to pick.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Airsoft Sniper Forum
240K posts
21K members
Since 2006
A forum community dedicated to Airsoft Sniper firearm owners and enthusiasts. Come join the discussion about optics, gunsmithing, styles, reviews, accessories, classifieds, and more!