Airsoft Sniper Forum banner

1 - 11 of 11 Posts

·
Registered
Joined
·
16 Posts
Discussion Starter · #1 ·
Hi everyone,
I'm customizing my WELL MB03 (VSR clone). I'm from Italy and we can play with 1 joule guns.
I read everywhere that I should get the Kit from AirsoftPro webite (spring guide, spring, zero trigger and piston), but it has been out of stock for months. I tried to mail them but they told me they're working on the new version of the kit and nothing will be available for at least 2 months more.
I don't really want to wait 2 months (or more). But I really need to change those parts (I already changed barrel and hop-up) since stock ones really suck.
Is there any good alternative to this kit? Or I just need to wait 2 months+ because there is nothing as good as this kit in the market right now?

Any tip will be appreciated.
 

·
Registered
Joined
·
5 Posts
The Action Army 90 Degree Zero Trigger and Piston set is often recommended. Action Army also sells a spring guide separately. Laylax and Rapax springs are also often recommended.
 

·
Registered
Joined
·
29 Posts
1 joule? Unless your trigger sear and piston are failing, you should be fine current upgrades for now. Maybe add a concaved nub to with Action Army Hop Up chamber, and verify proper airseal. Or are you tinkering/tuning this rifle?
 

·
Registered
Joined
·
16 Posts
Discussion Starter · #6 · (Edited)
1 joule? Unless your trigger sear and piston are failing, you should be fine current upgrades for now. Maybe add a concaved nub to with Action Army Hop Up chamber, and verify proper airseal. Or are you tinkering/tuning this rifle?
TBH at 1 Joule, any 90deg trigger is not going to benefit you that much over the stock.
Thank you both!
What happend is that now when I pull back the bolt handle, it doesn't lock the spring.So I opened it and I noticed the piece on the trigger box which blocks the spring (the long one, not the 45 degree one) just broke.
Now: I should just buy another 45 degree trigger since it is cheaper?
Also, is commonly known that stock piston and spring guide in the WELL MB03 are just so bad, so I assumed I thought it was a must to change them. Is there any point to buy expensive spring guide and piston or a chinese one on Aliexpress will do its job?
Sorry for my english.
 

·
Registered
Joined
·
29 Posts
Sounds like the perfect time to upgrade. As for advice, only you can answer that. What is your financial situation? Do you purchase cheap part and hope it holds until Airsoft Pro completes their new design? Or purchase something else?

If want to purchase higher end components now, there is Springer Custom Works has V9.2 and Budget triggers as well has spring guide and piston. Their piston is compatible with most cylinders: Action Army, Laylax, Mag, Maple Leaf, and stock. I would verify with them before purchase. Feedback for either of these two triggers has been very positive.

Action Army (Laylax Clone) has a trigger (available most places) and piston package as well.

What ever you decide, keep in mind after market parts may or may not be drop in ready ... slight modifications may be required.

And if you have trouble with installations, post here. I am sure someone will have the knowledge to assist.
 

·
Registered
Joined
·
16 Posts
Discussion Starter · #8 ·
Sounds like the perfect time to upgrade. As for advice, only you can answer that. What is your financial situation? Do you purchase cheap part and hope it holds until Airsoft Pro completes their new design? Or purchase something else?

If want to purchase higher end components now, there is Springer Custom Works has V9.2 and Budget triggers as well has spring guide and piston. Their piston is compatible with most cylinders: Action Army, Laylax, Mag, Maple Leaf, and stock. I would verify with them before purchase. Feedback for either of these two triggers has been very positive.

Action Army (Laylax Clone) has a trigger (available most places) and piston package as well.

What ever you decide, keep in mind after market parts may or may not be drop in ready ... slight modifications may be required.

And if you have trouble with installations, post here. I am sure someone will have the knowledge to assist.
Hi Thank you!
Well I was thinking to spend something like 100-120 EUROS between the trigger, spring guide and piston. But I don't mind the brand if the performance is the same. Here in italy I can buy Chinese spring guide and piston (metal or aluminum, whic is better?)compatible with MB03 for like 20 EUROS, and get another trigger box (like the stock one) for 30 EURO.
Since my limit is 1joule, is there any point in purchasing expensive spring guide, piston and trigger or I'll just do fine with stock/chinese ones? I ask because maybe piston can play a role in shot consistency if I don't have perfect air seal.
 

·
Registered
Joined
·
1,486 Posts
I would suggest the ESC works piston and trigger Sears in your case, as well as his spring guide.
Should be below €100 and he's in Italy so you have fast shipping and good communication.
 

·
Registered
Joined
·
16 Posts
Discussion Starter · #10 · (Edited)
I would suggest the ESC works piston and trigger Sears in your case, as well as his spring guide.
Should be below €100 and he's in Italy so you have fast shipping and good communication.
Hi Thank you!
Never heard of them, may I ask you if you have any experience with their products? also I never used a trigger like the one they have, how does it work?
 

·
Registered
Joined
·
1,486 Posts
I have 2 friends that have his piston and spring guide, and they both really like them.

His sears are a 90* version of 45* sears, so you just replace the old parts in your trigger with his.
They are not great for high power, but below 2J they are awesome as they are pretty cheap and really simple.
 
1 - 11 of 11 Posts
Top