[doubledeluxe4]

So I just got my JG VSR/BAR 10 in the mail from evike today. I opened the box, put the rail and scope on, took it outside and shot around 50 bullets and then it got locked up and I couldn't cock it anymore. Took it apart and when I got to the spring guide it wouldn't come out...so i skipped that step and took the trigger thingy apart and after I heard the gun shoot (nothing came out) and the spring guide still wouldn't come out!

 

[Mattyboyzhere]

The stock VSR cylinder cant be tampered with unless you cut and remove the metal (rivit) ? I bought a teflon cylinder to resolve this issue and kept the stock as a spare..

Sent from my A0001 using Tapatalk

 

[doubledeluxe4]

What do u mean by metal rivit?

 

[bmr3]

Did you get a bar 10 or Tokyo Marui VSR10? If you have the bar 10 you should be able to unscrew the cylinder head and take pressure of your spring guide stopper, allowing you to remove it. If you have a Tokyo Marui then you will need to drill out the pin (rivit) to be able to access the cylinder set.

Either way, take pressure off the spring guide stopper and it should pop right out


Sent from my iPhone using Tapatalk

 

[doubledeluxe4]

I dont see that. On the evike web it says its a vsr10/bar/10 upgraded. The spring guide wouldnt even come out with a hammer so its stuck good

 

[bmr3]

That cylinder head looks like the one from my Well MB03. Have you tried to unscrew the cylinder head to take pressure of the spring guide stopper? I would try to avoid hammering on your receiver so you don't bend anything.


Sent from my iPhone using Tapatalk

 

[doubledeluxe4]

Is it a screw or a pull?

 

[bmr3]

Stick something like a Allen key in one of the holes to give you leverage and just unscrew it, lefty loosey


Sent from my iPhone using Tapatalk

 

[doubledeluxe4]

Stick something like a Allen key in one of the holes to give you leverage and just unscrew it, lefty loosey

Ok i got it

 

[doubledeluxe4]

I got it off but its still stuck. Looks like a gear thing with a wire inside it

 

[bmr3]

I think your describing your spring guide. It sounds like something happened at the factory and they some how jammed your spring guide and stopped together. I would try spraying WD-40 or some other lubricant down in the spring guide stopper and then use pliers to try to pull it out


Sent from my iPhone using Tapatalk

 

[doubledeluxe4]

I think your describing your spring guide. It sounds like something happened at the factory and they some how jammed your spring guide and stopped together. I would try spraying WD-40 or some other lubricant down in the spring guide stopper and then use pliers to try to pull it out

Sent from my iPhone using Tapatalk

I have tried but I might have to take it to a airsoft store

 

[bmr3]

I have tried but I might have to take it to a airsoft store

Please make an introduction post as you have you have exceeded your 5 post limit and it is a forum rule. It also helps other users to get a feel for your experience level with teching and airsoft in general.

Sent from my iPhone using Tapatalk

 

[SniperPenguin]

Okay, I get that he needs to make it and all, but instead of just telling him that with no help whatsoever on his problem you could've at least given him advice, instead of replying by just saying, "Make an introduction post."

 

[doubledeluxe4]

Introduction Post?

 

[bmr3]

Okay, I get that he needs to make it and all, but instead of just telling him that with no help whatsoever on his problem you could've at least given him advice, instead of replying by just saying, "Make an introduction post."

Did you even read this tread before making before making such a rude accusation? You would have noticed I did offer him advice, multiple times...

Sent from my iPhone using Tapatalk

 

[SniperPenguin]

Oh no, I did see that. But you responded to an unanswered question he had.

Anyway, I do see that he should make an intro post but a bit of help on his question would probably have been good too :tup:

 

[SniperPenguin]

Yes, it's a post introducing yourself to the forums and such.

Make it here: New Member Introductions & Tips - Airsoft Sniper Forum

 

[bmr3]

Oh no, I did see that. But you responded to an unanswered question he had.

Anyway, I do see that he should make an intro post but a bit of help on his question would probably have been good too :tup:

Are you stupid? I did try to offer help and the post you are referring to he said he was going to take the rifle to an Airsoft shop... How is that statement an unanswered question?

Sent from my iPhone using Tapatalk

 

[Rvl]

One suggestion.
If it was difficult to cock , I suggest you check the scope rail screws. If they are too long it presses on the cylinder.