CA M24 PDI PART OR LAYLAX PART? - Now with review

5694 Views 22 Replies 5 Participants Last post by headshot06, Dec 1, 2011

headshot06

Discussion Starter · Nov 17, 2011

Hi Guys, I'm Andrew from Jakarta, i need some advice from you guys.

So basicly i'm using almost all laylax part for my M24 CA
My set up:
- PDI innerbarrel 6,01 515mm
- PDI Hop Up Chamber
- PDI W Hop Up Rubber
- PDI Barrel Spacer 4 Pieces
- Laylax Piston 3 Element Purple
- Laylax Piston Head Red
- Laylax Spring Guide
- Laylax Teflon Cylinder
- Laylax Bolt Handle
- Laylax Cylinder Head
- Laylax sp210

I need some advice on PDI Upgrade parts, because i'm considering to change my part all into pdi's. I need some information about the accuracy and durability. Which one is the best , laylax or pdi.

I already tried to browse a lot of website, but i couldn't find any concrete data, hoping you could help me on this one.

And the last thing i want to ask is about the PDI W Hop Up rubber, does anyone have better accuracy with others rubber hop up?

Thx a lot guys

PLEASE JUMP TO PAGE 2 IF YOU WANT TO SEE MY REVIEW on PDI PARTS, CAUSE FINALLY I CHANGED ALL MY PARTS INTO PDI'S

Save

21 - 23 of 23 Posts

Cheese Man

· #21 · Nov 24, 2011

If you do remove the mound, then the bucking is not really all that special. You could get better results with a prommy hard and some PTFE tape. The only thing that makes the w-hold special is the w-shaped nub/mound. Frankly, even the bucking you are using now would work fine.

By the way, you are holding the rifle with the stock attached, so I feel that it should be zeroed like that too, but that is just my opinion.

Save

headshot06

Discussion Starter · #22 · Dec 1, 2011

Thanks cheese man for your input, well the problem i have is the way the otterbarrel installed on my stock. It's miss align for sure, it causing my hop chamber miss align also. Therefore i have to align my scope crosshair with my outerbarrel without my stock installed.

Save

headshot06

Discussion Starter · #23 · Dec 1, 2011

Well finally i change all my internal into pdi, except the trigger, i still use the stock one because the triggerpull is very light.
Below are the list of my upgrade, and i will give some review also from my personal opinion.

Internal
- PDI Innerbarrel 6,01 - 515mm
- PDI Hop Up Chamber
- PDI W Hop Up Rubber
- PDI Barrel Spacer 4 Pieces
- PDI Tappered Cylinder Head
- PDI Piston VC
- PDI Spring Guide
- PDI Palsonite Cylinder
- PDI Bolt Handle
- PDI End Cap
- PDI SPR 250 Spring
- FPS stable at 470 With madbull 0,43 black bb

Personal review compared to laylax part:

Pros:
1. Accuracy and grouping quite significantly better
2. The bolt pull is much more smoother than the laylax teflon
3. The bolt pull is significanly lighter ( it feels like using the laylax sp170) and i'm using the spr250 spring
4. The bolt handle design makes easier to pull in the correct way.
5. Significantly more silenced
6. Triggerpull is lighter than using sp 170

Cons:
1. The end cap screw is easily loose after 2 magazine shots. Well a locktite could solve this problem
2. The laylax cylinder looks more durable than laylax, and it's a little bit heavier also.

Well basicly i got the grouping and fps i desire, i hope this review could help you guys also.

So i did a shooting test with a card board from 16 meters (52 feet) after a lot of adjustment with my hop up. Thank goodness i got pretty good grouping ( well that is my personal opinion, i do not know about you guys)

UPDATED 6.12.2011 with a little bit more tuning:

Below you could check the biggest circle target 22 cm diameter, and the circle inside

See less See more

Save

21 - 23 of 23 Posts

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.

Top Contributors this Month