[nelsonho396]

Well my Bar 10 has been lying dead for a good long time in the closet and I felt that need to revive it back to working order.
The only thing wrong with my Bar 10 was the broken hopup.

So this is what I am planning to possibly get.
Replacement JG Hopup chamber 12 dollars why not.
http://www.evike.com/product_info.php?products_id=30786
King Arms Bucking 15
http://www.evike.com/product_info.php?products_id=28401
Spare mag 10 dollars.
Modify 6.03 VSR10 barrel.
http://www.evike.com/product_info.php?products_id=36802
.3 bbs.

This is probably going to be my cart. Would it be good. Throwing in a 20 percent off coupon too and being at the walk in store.
Sorry this is a noob question but would this be good and what would you change. Please note I don`t have much money and I`m just reviving a old gun. Please be respectful and don`t say to me to go screw off or something like that...

 

[Cheese Man]

Buy the TM precision hop chamber, it comes with a decent barrel, and a good bucking. A little extra, but you get what you pay for...

 

[nelsonho396]

I found one on AA but its not in stock. http://www.airsoftatlanta.com/Tokyo_Marui_Brass_Barrel_New_Chamber_airsoft_VSR_p/17961.htm
I plan on fielding it on a New Years Op. I might as well run with a cheapie revival. I just need to shoot accurate and then I`m good.
Also what do you think of the barrel. I`m most likely going to have to buy a new barrel my old one is bent.

 

[WorstInFinlanD]

For cheapo and accurate... It's a tough call, but with a nineball bucking and a tm precision chamber you should be shooting g&g 0.3g bbs to chest 9/10 times from 30 yards.
Did bar 10 shoot around 400 fps out the box? If it shoots 300 fps, then i recommend m120 spring, you are really going to want that 70 fps increase. You can run it for a summer and then trigger sear is going to crack, by that time you should have enough money for deepfire searset.

 

[scar527]

You should look into a Danger Werx hop arm. I have one and it is outstanding, and a friend runs one in his stock bar-10 and it has enough hop to use .36's out to 60-70 yards(@ 400 FPS).

I have gotten hits at 90 yards with my 531fps setup.

 

[nelsonho396]

I have ~450 fps with .2 Problem is worst I can`t find a tm vsr10 hopup. Would the Matrix .3 be too heavy by the way should I go with G&G standard .28
I finally found the arm. http://dangerwerx.wordpress.com/2011/10/27/vsr-levers/#comment-7
It seems to be just a arm the is straight no like v notch in it. Also Worst I don`t see any trigger sear damage yet. Also can`t find a deepfire unless I ship over seas which is expensive.

 

[Cheese Man]

Boom. 10 seconds on google = http://shop.ehobbyasia.com/tokyo-marui-precision-brass-barrel-and-new-chamber-set-for-vsr-10.html

Just remember, you get what you pay for.

 

[nelsonho396]

Oops. -1 google skill for me. I may consider that but I don`t like overseaing if thats a word. I`ll just look around and see.
Oh yeah also I am considering a P* fusion engine drop in so that why I`m going very cheapie. I saving up for something but that going to take some time.

 

[WorstInFinlanD]

Don't ever use matrix bbs, just don't.
About bb weights on sniper, you should always use the heaviest bb if you have enough hop, if it underhops, get lighter bbs.
I got purple nineball and flat hop up arm nub, overhopping 0.25 at zero hop, I'll test 0.4 before doing anything to it.

 

[nelsonho396]

Worst actually I had really good experiences with Matrix bbs and they seem to be really good. Of course I always wash them before I use them. But they seem to be good.

 

[nelsonho396]

Anyone know if the Modify Vsr10 barrels are any good?