[bengreen]

Righto, i got my TM Gspec a while ago, i got it for £60 (problem with the trigger mech and bolt) was a quick fix. However i had to swap the bolt from my BAR 10 into the gspec, as the cylinder head would rip off after a few shots. I'm recently getting double feeding problems from my rifle, i'll pull the bolt back, push it forward and it won't go all the way in, i have to then pull the mag out and let the BB's drop out. It's not really what im wanting, it means i lose a lot of ammo and it can be incredibly annoying when im going for the shot!

I've got ASPUK upgrades (VSR Set) in the bolt and in the trigger mech (sears). I also have a falcon hop up rubber (new). Could this be a rubber problem? perhaps it isnt broken in yet? Or is it a bolt or hop problem?

I am also sure i am not loading it, then cocking it again.


Thanks!

 

[bengreen]

im pretty certain both of these things are fine, im somehow suspicious of the bolt; i dont know why.

 

[bengreen]

I did reseat the front screw, i did a few mags in my garden (while zeroing) and it didnt jam once, so im hoping that could be a fix, ill keep you updated though

 

[bengreen]

Just found out today my front screw is now chewed! Fantastic It isnt completely done yet so there could possibly be some saving it, any tips?

 

[bengreen]

Trouble is, its in my rifle i cant get it out! Currently i dont need to, but when i do need to, im gonna need to know how

 

[bengreen]

Thanks so much!

 

[bengreen]

How would you recommend doing that?

 

[bengreen]

Annoything thing is i dont have a dremel!

 

[bengreen]

Found out some more on my double feeding. In my mag part, theres a hole under the part where the point of the mag goes into the hop. and when im cocking it, i guess more than one feeds into the hop and one falls back and stops the cylinder head from going all the way forward and loading into the hop. I have no idea why this is Any ideas? I still need to get the front screw out, but im sure ill find a way.

 

[bengreen]

Well, once i get the rifle open ill swap it out for a BAR 10 one In the mean time ill have to survive

 

[bengreen]

I'm from the UK guys so its a bit of a problem ordering from USA. Gonna try get the screw out sometime tomorrow i think. I used a JG bar 10 cylinder instead of the GSPEC one, is there any noticeable difference?

 

[bengreen]

Alright, well thats fine - ill have a crack at getting this screw out tomorrow, should be able to get a replacement. Ill swap out the bb stopper tomorrow.

 

[bengreen]

luckily i managed to get the screw out! Because i hadnt gone over the top in chewing it i just tilted the allen screw and got it out, gonna make it into a flat head screw now.

edit: I have just looked at my bucking, it was turned slightly so the 'window' where the arm presses was pressing on a bit of metal too, i changed it so it no longer does this; i also swapped out the bb stoppers. Will be able to test tomorrow as it is 11PM here

 

[bengreen]

Went out and tested it. Still happens, this is so frustrating. It double feeds sometimes and fires two, sometimes it doesnt let me shoot at all (because its fed like 5 into the hop and its block the cylinder). Im honestly running out of ideas Could it be the hop bucking itself?

 

[bengreen]

The spring is there, its still springy too, i do have 3 other mags so ill test with them

 

[bengreen]

Yeah it really is a pain, especially when it clears out half of a mag just trying to get it working again! But im gonna try a new mag, then try some other bits like what you've said.

Edit - went out for a test. My conclusions are, it can't be my bb stopper, i popped a bb in there, and vigorously shook my rifle, that thing wasnt going anywhere. Secondly, changed from my original TM mag to an unbranded one (i believe 55rounds) and shot around 50-60 BB's through it, didnt double feed once, i had the odd low baller BB but i think that could be a barrel problem (i need to clean it).