Airsoft Sniper Forum banner
1 - 19 of 19 Posts

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #1 ·
I took this, my G&G M14



and turned it into this, a KART EBR chassis/G&G hybrid



And they said it couldn't be done, HA!, I laugh in the face of the doughters


Action shots ;)





A small, temperary, comprimise due to lack of funds. Battery taped into stock that has had to be fixed perminantly open. As soon as funds alow an AB MOSFET and Li-Po will go in the fore grip ;)



Cheers

VA
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #3 ·
Only 350fps, British laws :( Anything thats over 368 and self loading is what the law here calls a 'section 5 Fire Arm' and there fore illegal :( some sites allow upto 425 so long as full auto is permanently disengaged but they sadly are few and far between :(
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #6 ·
sticks13 said:
Looks good,

I would really appreciate a painting guide :). Did you brush this one too? It doesn't look like it was sprayed(a good thing).

sticks
Sorry mate its sprayed, but with a desent brush and an artistic flare you could do it with a brush ;)
 

·
Registered
Joined
·
100 Posts
Phridum: I know how to spray guns but I didnt know what his meathods for brushing guns were, thanks for the thought though!

Vindicare: I was mainly wonder what paints you use(for brushing)? It still looks good though. What do you use for your stencils? I have only used plasticard so far but its a little hard to work with.

sticks
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #9 ·
I use Tamiya XF paints regardless of wether I spray or hand paint mate. Sometimes I'll give it a light coat of Matt Varnish to protect it but that very much depends on if I have any in stock ;) I dont use stencils, everything you see here is done free hand


Phridum; the M14 in the first picture is hand painted


Action shots





 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #11 ·
Its just a block of hard foam glued to the stock and then shaped and rounded at the edges with a sharpe knife and sand paper :)The Butt extender is the same stuff too ;)
 

·
Registered
Joined
·
18 Posts
Hello,
Where did you get this smal 10 rnds size magazine for M14/21. I have long 20rnd size (hi-cap 280bbs) for and was looking for small to make it looks more like M21. Can you send me a link or info where I can order it?
Thank you
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #14 ·
GLOBAL HAWK said:
Hello,
Where did you get this smal 10 rnds size magazine for M14/21. I have long 20rnd size (hi-cap 280bbs) for and was looking for small to make it looks more like M21. Can you send me a link or info where I can order it?
Thank you
Check 'Short G&G mag' out. Bottom of longrange AEG title page.
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #16 ·
First up chap, I do believe that you have already been warned about reviving old threads please try to refrain from doing so ;) To answer your question, nothing at all if you like being just like everyone else
Go have a look in 'Paint your wa....gun' and see if you could achieve any of my paint schemes with a spray can and a branch of a tree ;) There is a subtle difference between a random person wandering past and saying casually 'nice gun' and having six or seven grown men jumping up and down trying to hold your gun because they think your paint job is the best they have ever seen and could you do something similar for them
 

·
Premium Member
Joined
·
802 Posts
Word. (Sorry I just had to state it after vindicare's post. Or do I have to make a new thread just because of this one word?)
 

·
Registered
Joined
·
1,045 Posts
Discussion Starter · #19 ·
Sadly no mate :( I have new project on the go at the moment, based on a Dboys SPR Mk12 Mod0, and it is going to be quite different as I have mission specific agenda to achieve ;) I will be doing a Photo thread on how and why when she is complete
 
1 - 19 of 19 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top