Airsoft Sniper Forum banner
41 - 59 of 59 Posts

·
Registered
Joined
·
38 Posts
Discussion Starter · #41 ·
I'll take some pictures of the speed loader adapter tomorrow or Thursday, Depends on how tired I am when I get home from night shift tomorrow morning ;)

Yea the map pro almost halved the min-max range of my best mag, but still wasn't good enough to field had a 10 fps variance from max to min on the best run. I have a few ideas I'm going to try when the weather gets better.
 

·
Registered
Joined
·
38 Posts
Discussion Starter · #45 ·
I bought some .338 pouches from Warrior Assault Systems, they seem to work nicely.
But I'd guess it all depends at what you can get at a resonable price where you live.
 

·
Registered
Joined
·
38 Posts
Discussion Starter · #48 ·
Just be careful that they aren't too deep, can be hard to get them out then.
I tried using the SR25 mag pouches I bought for my well.. SR25 but they were really tight and deep. Was a pain to get the m40 mags out of them.
 

·
Registered
Joined
·
118 Posts
So I have been testing the rifle and things are going pretty well. I saw some differences in power output from the magazines (although all were pretty consistent, just different fps vs each other). I fixed this by opening and lubing each one. Now I'm sure I will have silicone in the barrel/hopup for a little while but at least it's gotten the power from each mag pretty consistent now. Really happy with the power output of this thing.

Regarding accuracy though, it is strange. I'm really not getting consistent results. Or in other words I am inconsistently consistent. It will shoot really well for a bit, and then it will have some fliers forcing me to adjust the hopup to correct. On other rifles, once the gun is dialed in, it really feels quite dialed in and doesn't need many changes. Perhaps this is due to the potential for silicon to have entered the bucking due to my re-lubing of the mags, but maybe not. I did clean the bucking well but it's hard to isolate aerated oil.

Another area for these fliers and need to keep fiddling with the hopup could be the hopup chamber. I have an autobot 70* bucking and wiitech unit installed but also have the stock hop chamber in a bag to replace if needed. Given the winter weather and darkness I don't have a ton of time to swap parts and still make it outside in daylight to test so I was hoping to ask the group: Out of the owners of this rifle, have you compared the wiitech hop chamber against the stock unit? Does one seem to function better than the other? There are many reports lauding the accuracy of the gun with stock parts so if the consensus is that the stock hop chamber is fine I could switch back.

Thanks for your help!
 

·
Registered
Joined
·
167 Posts
I got stock hop up chamber. The only inconsistency I see is the FPS, bbs are flying straight but the hop seems to be impacted by those ups and downs in the power.
 

·
Registered
Joined
·
4 Posts
My new weapon arrived today only had a can of red gas, I know I know I should have waited to run the dry gas but still waiting on the fill cap for the propane can. So people what should I do first all is bone stock
Once I have the dry gas I will strip and clean then throw a load of 0.25 that I have to run her in a bit. I have some 0.40 ready to load up once I have done the above. Question is do I even waste time running her stock or get the barrel order in now?
 

·
Registered
Joined
·
4 Posts
Thanks Dimitri MdP 👍🏼 I will run As is then for a bit see how we go. I hear your the man in the know with this weapon. in standard trim what weight BB would be best in your opinion
 

·
Registered
Joined
·
167 Posts
Just posted a chrono test. First shot is always hot no matter what, then things start to get better. Anyway I love that rifle.

 

·
Registered
Joined
·
1 Posts
I need to remove the outbarrel but I am not able to remove the second part after removing the interbarrel, any solution?
 
41 - 59 of 59 Posts
Top