Airsoft Sniper Forum banner
1 - 20 of 29 Posts

·
Registered
Joined
·
241 Posts
Discussion Starter · #1 · (Edited)
Hey guys, I'm pretty okay with my L96 knowledge but I know nothing about VSR's. I'm considering in investing in a TM VSR as my lighter rifle and and I would like to know a few things about it. I will be taking the Laylax route.

First and foremost. Assuming I do get a VSR it will definitely be the G-Spec. I love silencers but I know the barrel fits a 303, not including the silencer. How long is the silencer?

As far as hop up goes, there's 3 choices And there's the R-hop but as far as I know it's integrated with any of the three hop up chambers.
My hop up choices.
-Stock hop up(I've heard the VSR has decent hop up when used with r-hop)
-Tokyo Marui Precision Brass Barrel & New Chamber Set for VSR-10(430mm)
-Laylax VSR-10 AERO Chamber NEO(I've never heard of this up until today.)
http://www.airsoftatlanta.com/Laylax_VSR_10_AERO_Chamber_NEO_p/58466.htm

Which is the best?

My Barrel choices.
-Laylax 6.03(430mm) VSR-10(I'm not sure if it works with upgraded hop up chambers)
-Prommy 6.03(407mm)AEG

Everything else I pretty much know.
-Laylax 450 fps spring(I'll look for that later)
-Laylax Teflon Cylinder
-Laylax Cylinder head
-Laylax Z-Trigger w/ Orange piston
-Laylax Spring guide 9mm
-Laylax Piston head
-If I go with the stock hop-up, then a nine ball(purple bucking) If I do one of the upgrade hop-ups then I'll use the W-hold.

Anything I'm doing wrong or any suggestions? I really don't know much about VSR's so feel free to say whatever you feel would be better.
 

·
Registered
Joined
·
568 Posts
You are getting a lighter rifle, but you still are not going to get 303mm barrel? If I were you, I would get the same as you, but a 303mm barrel, cut the m150 spring so piston won't hit cylinder head, making the gun dead silent, and I would still hit ~400 fps with 0.36, and would reach nice 200ft easily.
But if you want that longer barrel, get tokyo marui precision chamber, it comes with a 430mm tbb.
 

·
Registered
Joined
·
909 Posts
You are getting a lighter rifle, but you still are not going to get 303mm barrel? If I were you, I would get the same as you, but a 303mm barrel, cut the m150 spring so piston won't hit cylinder head, making the gun dead silent, and I would still hit ~400 fps with 0.36, and would reach nice 200ft easily.
But if you want that longer barrel, get tokyo marui precision chamber, it comes with a 430mm tbb.
I agree with the 303mm barrel. If you're looking for one, I have a PDI 6.01 303mm that hasn't been used very much at all that I'm looking to sell. PM if interested.

Other than that, your build looks good. I'd maybe go with the TM Precision Chamber and the Nineball bucking, or just stick with the stock chamber with mods and then get the Precision Chamber later on.
 

·
Registered
Joined
·
241 Posts
Discussion Starter · #7 · (Edited)
That's what I was thinking. Okay, so the standard barrel fits 303mm but with the silencer it can fit the 430mm or 455mm. I meant light rifle as in it's not nearly as long or heavy as my L96. With the silencer on the VSR is about 113cm. My l96 with a silencer is 140cm. And heavy And I don't like rifles without silencers.
I'll definitely consider it. But what's better the TM chamber, or the laylax neo chamber? And is the TBB that comes with the TM chamber any good?
 

·
Registered
Joined
·
568 Posts
It's good, not as good as pdi or prome, but it's close.
With 303 you can take off/put back the silencer, and I have learned to appreciate that. :p Assault rifle lenght, no MED (it was stock), light weight, with nice accuracy. With silencer, silent past 5 meters.
 

·
Registered
Joined
·
241 Posts
Discussion Starter · #10 ·
I don't mind the VSR with a silencer. And I prefer the extra range and accuracy. With the silencer, the VSR is still shorter than an l96, and less than half the weight.

And Can the R-Hop be used with the TM Chamber?
 

·
Premium Member
Joined
·
3,494 Posts
The reason the G-spec won't intially fit with the TM precision chamber is due to the fact that the suppressor does not allow inner barrel to pop through it. Just need to file the suppressor window down a bit.
 

·
Registered
Joined
·
909 Posts
Why wouldn't it be? It's a longer barrel.
It's a common misconception in the airsoft world, but unlike real steel, barrel length doesn't do much at all. People have been able to achieve sniper distances with gas pistols with an HPA rig.

Longer barrels increase accuracy.... no range...
Actually, a longer barrel and decrease the accuracy if it's too long. Even if it's slightly longer, it won't increase accuracy. What really increases the accuracy when replacing a stock barrel is the consistencies of the barrel diameter. This is why upgraded barrels are generally better than the stock barrels. I've had good success with just polishing my stock barrels though.
 

·
Registered
Joined
·
241 Posts
Discussion Starter · #19 ·
It's a common misconception in the airsoft world, but unlike real steel, barrel length doesn't do much at all.
I don't know about that. The longer barrel from the m1911 upgrade by madbull makes a huge difference in range and accuracy. Maybe there's a difference in rifles since they already have long barrels but just saying.
 
1 - 20 of 29 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top