Airsoft Sniper Forum banner
1 - 7 of 7 Posts

·
Registered
Joined
·
5 Posts
Discussion Starter · #1 ·
Hey, new here but I've been lurking long enough to get a few answers for I've been looking for. For a while I was puzzled about what parts to get for my m24 but no I think I got it. a Prommy 6.03 TB, and an advanced cylinder kit. I'm keepin' it fairly simple for now. I also had the bad luck of having my bolt handle fall off so I do need one of those as well.

What I need to know is Where can I find these parts in the US? I've looked at Airsoft GI, Evike, and Trinity Airsoft but they all seem to be lacking the bolt handle. I figure Evike is my best bet out of the 3, but are there any real big ones I'm missing? Preferably that have all the parts I need? Thanks!

Eric

Edit: Okay so I think I might be able to fix the handle, after some tedious searching I found the missing screw. Although I do have a new question. Do I need a longer Tighbore if I want to put a mock silencer on my M24? Thanks again for answers!
 

·
Registered
Joined
·
1,386 Posts
If it is longer than stock, you will need a suppressor and suppressor adapter. The stock length is 515mm, and comes AEG style, so what I would suggest are these parts.

I am pretty confident you can use an APS2 cylinder with the M24 with an APS2 bolt handle. I hope someone else can verify on this soon. Guarder and PDI make a good stainless or Palsonite cylinder, I don't care for the Teflon, it has verified power loss.

If you can retain the original cylinder or buy a custom one, you can also get this.
http://poweredgeusa.com/Power-Edge-Custom-Works/Maruzen-Sniper/PEC-APS2-Set

With this for the piston cup.
http://poweredgeusa.com/LayLax/Maruzen-Sniper/Laylax-PSS2-Piston-Head-Cup-APS2
 

·
Banned
Joined
·
215 Posts
APS cylinders with APS handles work

The stock cylinder will not last with a 500+ setup

I would highly advise staying away from the Advanced cylinder kit, they are junk.

509mm AEG cut barrels fit perfectly

x-fire.org has the best PDI M24 parts. Shipping from them is always fast to.
 

·
Registered
Joined
·
5 Posts
Discussion Starter · #6 ·
Thanks everyone for the help! After reading, and researching (and fixing my bolt handle) I believe I narrowed down my list to exactly what I want.

I need the PDI Silencer Adapter and the G&G SS-80 Silencer with a Prommy 6.03mm 590mm TB. That's the first chunk of upgrades I'm getting for my rifle. Eventually I'd like to get a PDI Hop up Chamber too.

The question is, should I get the PDI Palsonite Cylinder Kit with the Vacuum Piston before a hop-up if accuracy is my priority? both items will be purchased after the tightbore and stuff. Also, I don't want my rifle shooting over 550 fps so would I have to get a different spring for the PDI cylinder kit to take away power?

Finally, I've got a little off question about scopes... I think I've narrowed my decision down to 2 scopes, which is a better scope (to your knowledge)
http://airsoft-club.com/shop/scope/illuminated/m3-3-5-10x50-50mm-red-green-illuminated-mil-dot-rifle-scope or
http://www.airsoftpost.com/product_info.php?cPath=32_180&products_id=27198

Thanks again everyone, all help is appreciated!

EDIT: Oh, also...why do people get the zero trigger assembly if the trigger can be adjusted on the M24?
 
1 - 7 of 7 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top