[Masada]

Alright, after too much time I finally have some more VSR Ultimate receivers ready for sale. Technically this is the second batch, but this time there are only 5 available. No group buy either, these are ready to go right now.

For those that haven't yet seen, here are some quick points about these receivers:
• One-piece combined receiver and outer barrel, CNC machined from 7075-T6 aluminum
• Hard coat anodized
• Marui VSR spec (will fit larger PDI cylinders though)
• CNC machined POM full-length cylinder sleeves
• 18 inch (from "receiver" front) barrel
• Threaded front (M28x1mm threads)
• Pre-drilled for Wolverine HPA setups
• Matching custom CNC machined rail and end cap included

As mentioned, there are 5 available (3 grey, 2 black). Each one comes with a rail and an end cap, and I am not offering any additional accessories this time. If you need something custom, just ask.

This batch differs slightly from the first set. The end cap design was modified so that the grub screw got more bite on the threads in the barrel. I also made the switch to POM for the sleeves as it is much easier to control tolerances and it still provides a very smooth bolt pull. The rear tang was adjusted slightly as well, though this was extremely minor.

Price for each set is $420 plus shipping and fees.

One of the grey receivers is what I'd consider slightly "blemished," so I am offering this one set at $400. The blemishes are very minor and should be covered by whatever stock you install as well.

I have some concave nubs available too. These were designed specifically around the Action Army chamber and they fully fill the hop up window. I have been getting a lot of positive feedback on these as they seem to perform very well.

Nubs are $5 each.

*All pricing is in USD
*I'd very much prefer PayPal only

 

[FMP Airsoft]

Will the nubs fit a standard VSR hop up chamber?

 

[SiliconeSword]

Will the nubs fit a standard VSR hop up chamber?

As long as you have an arm that will take it.
I think that there is the Panthera and some other arm on Skirmshop that might work, but that sort of defeats the purpose of buying a Masada nub.

 

[Masada]

Will the nubs fit a standard VSR hop up chamber?

I honestly don't know, and I don't have a standard VSR chamber to test it with. I'm guessing they would fit fine, but maybe would need a different arm to actaute correctly? It's been a while since I've messed with a factory VSR hopup chamber so I'm a little fuzzy.

 

[Blind Sniper]

Hey FMP sorry to chime in again but a stock chamber vsr window is wider than an action army window. The panthera nub (and masadas nub I’m pretty sure) are designed to fit in the entire as window. I believe it helps with alignment. So they will definitely work in a stock chamber as long as you have an arm that holds it like mentioned! (I’m about to check if I have one)

 

[SiliconeSword]

Will the nubs fit a standard VSR hop up chamber?

You had better get a new gen Maple Leaf arm, AirsoftPro, Panthera, or whatever else there is since I think it would be hard to center one of those nubs.

 

[Masada]

Just FYI, I still have a couple receivers left, though both black ones are gone.

At this point I'm pretty confident in saying that these are the nicest airsoft bolt-action receivers/barrels on the market. Obviously a very high end piece, but for those rare ultra-high end builds: this is it.

 

[JFRABAT]

Any of those receivers left, by any chance?

 

[Blind Sniper]

Don’t provoke him to start another batch or I’ll be forced to buy one sooner than planned 😁🤘🏻

 

[mwrose777]

Don't want to speak for him, but I think there's still a couple floating around....I'll txt him and let him know y'all are asking

 

[Masada]

Ya I have a couple of the grey ones left.

 

[Hunter424]

Can you make one with a longer barrel?

 

[Masada]

Can you make one with a longer barrel?

I could, however it would be really expensive. Making one receiver at a time is pricey.

 

[Blind Sniper]

I am 10/10 reaching out to purchase one this year. It’s a very important part that I need for a Bolt build!!

 

[Masada]

At some point I need to get around to making that follow-up design I had for this.

 

[terry44]

hello

 

[Thwack.]

is there any threaded endcap you recommend for a 14mm - surpressor?
I am seriously considering buying one of the receivers

 

[Masada]

I believe the Novritsch one will fit, though I havent tried it. I have one custom threaded end cap still available if you wanted.

Edit: nevermind, his are CCW and mine are CW

 

[Blind Sniper]

Novritsch’s adapter is negative threads. I found out the hard way. BUT if you have an AA twist barrel, you can ditch their stupid end cap and use the Novritsch one. Then you don’t have 14 adapter and suppressor pieces coming loose when you tighten another.

 

[Masada]

Wait the main threads that connect to the outer barrel are negative on his?