[freskhu]

The 170 euros you save, you put in upgrades that are much better than what Marui offers stock. Yes, Jing Gong parts are not the best stock. But their cylinder and cylinder head are fine. And at least you can open the cylinder for upgrading, unlike Marui.

is Action Army similiar to airsoft pro?

 

[freskhu]

So my buying list for the bar10:

- airsoft pro trigger 90º with piston
- inner barrel PDI Raven 6.01
- PDI W hopup
- Hopup arm

Should i change the hopup chamber?

 

[Zerosliver]

So my buying list for the bar10:

- airsoft pro trigger 90º with piston
- inner barrel PDI Raven 6.01
- PDI W hopup
- Hopup arm

Should i change the hopup chamber?

Hard to say. The airsoftpro/dangerwerx metal arm should help with the performance. But I'd recommend getting the Action Army chamber instead, it solves all the issues of the stock chamber.

And I have no experience with PDI raven products.

 

[freskhu]

i cant find AA in here, probably airsoft pro chamber will be ok?
The Raven PDI is just for PDI chambers, i will buy a deepfire, in here many people says they are good.
Thank you for your help

 

[Reliku]

I'd look again for an AA chamber. Really, I can't say there is any chamber out there that'll get remotely close to it.

Also consider an AA barrel, they're pretty decent for the price. They have a proper barrel cut that will allow a W-hold bucking to work. I have no experience with deepfire, but I'd recommend action army any day :tup:

 

[freskhu]

i will try to find a store in europe for action army ^^

 

[1tonne]

Like Reliku said. You will not find better than the AA Chamber. With the stock one you will never get 100% seal like the AA Chamber. Also, their barrels rock.

 

[GBB]

I installed a AA chamber today and noticed an increase of 15 FPS over the stock chamber. This is with an 430mm 6.05mm PDI barrel.

The airseal is epic. I did remove the outer alignment ridge and the nub mound + inner alignment ridge to incorporate the R-hop, but good stuff. AA parts are it.

 

[Zerosliver]

Yeah, I'm kind of devastated that I sold my bar10 before trying out that chamber.

Still, I might do an ultra budget project in the future, using the chamber and some other cheap parts.

 

[freskhu]

ok, i bought a tm vsr... the price is low in here at the moment.
It's hard to get parts from action army, the price is almost the same as laylax.
Regarding the TM inner barrel stock, can i use a W hop up bucking with it?

 

[Zerosliver]

ok, i bought a tm vsr... the price is low in here at the moment.
It's hard to get parts from action army, the price is almost the same as laylax.
Regarding the TM inner barrel stock, can i use a W hop up bucking with it?

Yes, it will work out fine. Just make sure for optimal usage to get an action army chamber or at least a metal flat type hop-up arm.

 

[freskhu]

i will buy now from airsoft world the chamber... It will cost near 100€.
Regarding the pistol for secondary you said to get a glock 17, but wich brand? should i go for gas or co2?
thank you for your support

 

[Reliku]

Yes, that should work.

 

[1tonne]

Go for green gas. A lot of the CO2 pistols fire at 400+ fps which is not really a side arm

 

[freskhu]

In portugal arrived the new APS ACP guns... it's worth? i am seing many great and some bad reviews...

 

[freskhu]

I got an APS ACP 601 for secondary.

Anyone knows where i can find the R hopup kits in europe?

 

[freskhu]

i got most of the parts now:

- Airsoftpro trigger 90º+piston+spring guide (installed)
- W PDI hop up rubber (Installed)
- Foam on stock
- Teflon tape on hopup rubber and cilynder head

Since the 150 and 190 spring didnt arrive yet i tried to shot... It's worst than the stock one ^^ this are easy to install parts i dont understand! dont know what could cause that! Today i will receive the springs and the dangerx arm to test it.
The hopup chamber will have to wait couple weeks for delivery :/

I didnt buy a new cylinder, i drilled the pin, probably i damaged it?

 

[Zerosliver]

Maybe. I'd always suggest getting a cylinder anyway when doing spring work.

 

[freskhu]

hi there!
Well i had to buy a new cylinder and cylinder head! With the 150 spring the cylinder doesnt handle it and the cylinder head pumps out :S

 

[freskhu]

i have another issue
After install the 90º trigger set, when i pull the cylinder and i try to put it back in place the bolt handle doesnt go down freely, i need to force it! How can i fix this?